Where can I buy BeamerZ™?
Go to our authorized dealers section for more information and to find an authorized dealer in your area.
TO THE TOP
Can I turn BeamerZ™ on while driving on city streets?
State and city laws vary. We recommend that you check the laws in your area prior to street use.
TO THE TOP
How do I install the batteries?
To remove the cap, use a standard Phillips screwdriver and remove the 2 screws and washers. Place a 9-volt battery in the base of each BeamerZ™; standard alkaline or lithium batteries are acceptable. Replace cap using ONLY the screws, washers and o-ring provided.
TO THE TOP
What is an o-ring?
It is the black ring that fits in the channel of the base of the BeamerZ™. It is a gasket that provides a water tight seal for BeamerZ™.
TO THE TOP
What if I lose a screw, washer, or o-ring?
Contact a BeamerZ™ Authorized Dealer or the BeamerZ Corporate Office to order replacement parts.
TO THE TOP
How long will my BeamerZ™ run before I need to replace the battery?
Batteries should provide 40-60 hours of operation. BeamerZ™ automatically turn off after 90 minutes of use.
TO THE TOP
How do I turn my BeamerZ™ on and off and change the lighting pattern?
Use the key fob provided. Each time BeamerZ™ is turned off and on, the lighting pattern will change. BeamerZ™ will automatically shut off after 90 minutes of use. See the lighting pattern demonstration.
TO THE TOP
What do I need to do before I install BeamerZ™ to my wheels?
Clean and dry wheels to remove wax and polish. Wipe wheel center with isopropyl alcohol pads provided in BeamerZ™ package.
TO THE TOP
Where do I attach BeamerZ™?
Locate the center point of your wheel. DO NOT remove adhesive backing until you have located wheel center. BeamerZ™ must be attached to the center point. If you are unsure where center is, outline BeamerZ™ with a pencil and check for center point.
TO THE TOP
What if my center caps are loose?
Loose center caps should be secured with a removable silicone adhesive available at hardware and automotive stores.
TO THE TOP
How do I install BeamerZ™?
Once you have located wheel center, peel off adhesive backing. Press and hold for 30 seconds. Allow adhesive to cure for 1 hour before driving.
TO THE TOP
What if my wheels are irregular or have contoured surfaces?
Additional foam rings are included in BeamerZ™. Before removing adhesive back and adding the extra ring, be sure BeamerZ™ does not extend beyond the rim of wheel. If the extra foam ring is needed, peel the backing off of the BeamerZ™ and one side of the extra foam ring and press exposed adhesive sides together. Press and hold 10 seconds.
Then peel the remaining adhesive backing. Find center point of wheel and press and hold for 30 seconds. Make sure foam conforms to surfaces. Allow adhesive to cure for 1 hour before driving.
WARNING: BeamerZ™ adhesive is permanent! BeamerZ™ is designed for use on automobile wheels only and is not for use as a warning or safety device. DO NOT adhere to skin.
TO THE TOP
Can I install onto painted wheels?
BeamerZ™ may mar or damage painted wheels.
TO THE TOP
Can I install BeamerZ™ under any weather conditions?
Apply BeamerZ™ when it is dry and when the outside temperature is 50 F° to 90 F° (10 C° to 30 C°).
TO THE TOP
What if I need to remove BeamerZ™?
The foam adhesive rings will be destroyed in removing BeamerZ™, and new foam rings must be purchased from www.beamerz.net. To remove, pull BeamerZ™ away from wheel and use a razor knife to cut foam between wheel and BeamerZ™. Remaining foam may be cleaned off wheels and BeamerZ™ case by firmly rubbing with your thumb to remove all foam. Then clean off remaining adhesive with a soft rag and glass cleaner or isopropyl alcohol.
TO THE TOP
What if I lose my key fob?
Replacement key fobs may be ordered by contacting a BeamerZ™ Authorized Dealer or the BeamerZ Corporate Office. Key fobs are magnetic and should not be kept next to credit cards or other magnetically embedded products.
TO THE TOP
How do I clean my BeamerZ™?
Clean the case with a clean, damp cloth. DO NOT point high pressure spray directly at BeamerZ™.
TO THE TOP
What if moisture enters my BeamerZ™?
Remove cap and gently wipe away moisture. Allow to dry before replacing cap. Check to make sure your o-ring, washers and screws are in place and tighten with a Phillips screwdriver.
TO THE TOP